Metal construction drawing inspection engineer

Minimum Requirements: Understanding of lifting equipment (cranes, hoists, winches) Knowledge of rigging gear (slings, shackles, hooks, spreader beams) Sling angle calculations Load weight estimation & center of gravity determination Safe Working Load (SWL) & Working Load Limit (WLL) Load calculations Crane capacity verification Ground bearing pressure calculations Stability checks Wind load considerations Method statements Risk assessments Lift drawings Selection of proper crane configuration Equipment inspection checklists* Risk assessment capability Ability to troubleshoot lifting issues Contingency planning Decision-making under pressure ​​​​​​​Key Responsibilities: Prepare detailed lifting plans and method statements for routine and complex lifts Perform load calculations, crane selection, and rigging design* Verify crane load charts and lifting capacities Review and approve lifting equipment (slings, shackles, spreader beams, etc.) Conduct ground bearing pressure calculations Assess environmental factors (wind, terrain, obstructions* nsure all lifting activities comply with company and regulatory requirements Conduct toolbox talks related to lifting operations Investigate lifting-related incidents and recommend corrective actions Ensure valid certifications for cranes, operators, and lifting gear* Supervise critical and heavy lifts on-site Coordinate with project managers, site engineers, and subcontractors Liaise with crane suppliers and third-party inspectors Monitor lifting operations to ensure adherence to approved lift plans) Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00 Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their CV to the e-mail address in the Apply for job button.

Minimum Requirements: Proficient operation of SPMT control systems, including all steering modes and synchronized movements Strong understanding of load distribution, axle load calculations, and ground bearing pressures Ability to read and interpret transport drawings, method statements, and lift/transport plans High level of situational awareness in congested, high-risk work environments Effective radio and hand-signal communication with supervisors, banksmen, and rigging teams Solid knowledge of hydraulic, electrical, and power pack systems related to SPMTs Skilled in precision maneuvering of heavy and oversized loads under tight tolerances Competent in conducting pre-use inspections and basic fault finding Strong commitment to HSE compliance, hazard identification, and risk control Ability to remain calm and make sound decisions under pressure and time-critical conditions Team-oriented mindset with the ability to work closely with engineers and lifting crews Physical fitness and coordination suitable for long shifts and demanding site conditions Key Responsibilities: Safely operate SPMT units during heavy lift and transport operations in accordance with approved lift and transport plans Execute precise maneuvering, positioning, and alignment of loads under tight tolerance conditions Conduct pre-operation inspections of SPMT units, power packs, hydraulic systems, and control systems Monitor load stability, axle loads, steering modes, and ground bearing pressures throughout operations Follow approved method statements, risk assessments, and permit-to-work requirements at all times Communicate effectively with SPMT supervisors, engineers, riggers, and banksmen using radio and hand signals Respond promptly and correctly to abnormal conditions, alarms, and emergency situations Perform basic troubleshooting and first-line maintenance and report defects immediately Assist with SPMT configuration, coupling and decoupling of axle lines, and setup of power packs Ensure full compliance with HSE regulations, company procedures, and site-specific safety rules Maintain accurate operational logs, checklists, and inspection reports Support continuous improvement through participation in toolbox talks, safety briefings, and lessons learned Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.

Minimum Requirements: Crane operation & controls – Confident operation of tower, mobile, crawler, and overhead cranes Load chart interpretation – Accurate assessment of weights, radii, and boom configurations Rigging knowledge – Proficient with slings, shackles, hooks, and load balancing Mechanical awareness – Ability to identify issues with hydraulics, cables, brakes, and safety systems Strong safety mindset – Continuous awareness of surroundings, personnel, weather, and site hazards Regulatory knowledge – Familiarity with OSHA, local regulations, site rules, and inspection standards Risk assessment – Demonstrated judgment to know when not to lift as a critical safety skill Key Responsibilities: Operate cranes and related equipment in a safe, precise, and efficient manner at all times Assemble, set up, rig, and dismantle cranes according to job and manufacturer requirements Function as crane operator, rigger, and signal person as required by staffing and job scope Determine and operate within lifting capacities in strict accordance with load charts Operate cranes based on written, verbal, and hand/signal instructions Conduct daily and periodic crane inspections, reporting any safety concerns or deficiencies Complete job tickets, crane inspection reports, and all required documentation accurately Operate additional equipment including fleet trucks, trailers, and support machinery Follow direction from supervisors and senior personnel while showing initiative and productivity Perform work for extended hours, often in adverse weather or site conditions, to meet project deadlines Maintain consistent, punctual attendance and a strong work ethic Work as a team player, fostering respectful and supportive relationships with coworkers Perform preventative maintenance including lubrication, cleaning, fluid sampling, replenishment, and component inspections Repair or replace worn or damaged components on heavy equipment as required Report any incident, hazard, or unethical activity that could impact company safety or operations to the Risk Manager Act as a mentor to less experienced employees and support team development Maintain all required certifications as mandated by law and company policy Remain in a constant state of alertness and operate in a safe, responsible manner Perform other duties as assigned Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.