Cran operator

Minimum Requirements: Understanding of lifting equipment (cranes, hoists, winches) Knowledge of rigging gear (slings, shackles, hooks, spreader beams) Sling angle calculations Load weight estimation & center of gravity determination Safe Working Load (SWL) & Working Load Limit (WLL) Load calculations Crane capacity verification Ground bearing pressure calculations Stability checks Wind load considerations Method statements Risk assessments Lift drawings Selection of proper crane configuration Equipment inspection checklists* Risk assessment capability Ability to troubleshoot lifting issues Contingency planning Decision-making under pressure ​​​​​​​Key Responsibilities: Prepare detailed lifting plans and method statements for routine and complex lifts Perform load calculations, crane selection, and rigging design* Verify crane load charts and lifting capacities Review and approve lifting equipment (slings, shackles, spreader beams, etc.) Conduct ground bearing pressure calculations Assess environmental factors (wind, terrain, obstructions* nsure all lifting activities comply with company and regulatory requirements Conduct toolbox talks related to lifting operations Investigate lifting-related incidents and recommend corrective actions Ensure valid certifications for cranes, operators, and lifting gear* Supervise critical and heavy lifts on-site Coordinate with project managers, site engineers, and subcontractors Liaise with crane suppliers and third-party inspectors Monitor lifting operations to ensure adherence to approved lift plans) Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00 Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their CV to the e-mail address in the Apply for job button.

Minimum Requirements: Proficient operation of SPMT control systems, including all steering modes and synchronized movements Strong understanding of load distribution, axle load calculations, and ground bearing pressures Ability to read and interpret transport drawings, method statements, and lift/transport plans High level of situational awareness in congested, high-risk work environments Effective radio and hand-signal communication with supervisors, banksmen, and rigging teams Solid knowledge of hydraulic, electrical, and power pack systems related to SPMTs Skilled in precision maneuvering of heavy and oversized loads under tight tolerances Competent in conducting pre-use inspections and basic fault finding Strong commitment to HSE compliance, hazard identification, and risk control Ability to remain calm and make sound decisions under pressure and time-critical conditions Team-oriented mindset with the ability to work closely with engineers and lifting crews Physical fitness and coordination suitable for long shifts and demanding site conditions Key Responsibilities: Safely operate SPMT units during heavy lift and transport operations in accordance with approved lift and transport plans Execute precise maneuvering, positioning, and alignment of loads under tight tolerance conditions Conduct pre-operation inspections of SPMT units, power packs, hydraulic systems, and control systems Monitor load stability, axle loads, steering modes, and ground bearing pressures throughout operations Follow approved method statements, risk assessments, and permit-to-work requirements at all times Communicate effectively with SPMT supervisors, engineers, riggers, and banksmen using radio and hand signals Respond promptly and correctly to abnormal conditions, alarms, and emergency situations Perform basic troubleshooting and first-line maintenance and report defects immediately Assist with SPMT configuration, coupling and decoupling of axle lines, and setup of power packs Ensure full compliance with HSE regulations, company procedures, and site-specific safety rules Maintain accurate operational logs, checklists, and inspection reports Support continuous improvement through participation in toolbox talks, safety briefings, and lessons learned Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.

Minimum Requirements: Strong ability to read, interpret, and review structural steel drawings (GA, shop, fabrication, and erection drawings). Solid understanding of steel structures design principles (connections, load paths, tolerances). Knowledge of international codes & standards: AISC, ASTM, AWS, EN, ISO, BS. Familiarity with welding symbols, WPS, NDT methods, and bolted connections. Understanding of material specifications (steel grades, bolts, coatings, fireproofing). Ability to identify design errors, clashes, and constructability issues. Software & Digital Skills: Proficiency in AutoCAD for drawing review and markups. Working knowledge of Tekla Structures or similar steel detailing software. Ability to review 3D models and BIM coordination drawings. Comfortable using document control systems and drawing registers. Basic skills in Excel for tracking comments, revisions, and inspections. Quality & Inspection Skills: Strong eye for detail and accuracy. Understanding of quality control procedures and inspection workflows. Ability to raise RFIs, NCRs, and technical comments clearly and professionally. Knowledge of inspection & test plans (ITPs) related to steel fabrication and erection. Key Responsibilities: Review and verify construction drawings (shop drawings, fabrication drawings, erection drawings) for steel and metal structures. Ensure compliance with project specifications, contracts, applicable codes, and standards (AISC, ASTM, EN, ISO, AWS, etc.). Check dimensional accuracy, connection details, tolerances, and material specifications. Confirm constructability and coordination with architectural, civil, mechanical, and electrical drawings. Identify design clashes, omissions, or inconsistencies and raise technical queries (RFIs). Verify materials (steel grades, bolts, welding consumables) match approved specifications. Review welding details (WPS, weld symbols, NDT requirements). Ensure corrosion protection systems are correctly specified (galvanizing, painting, coating systems). Confirm compliance with safety and structural integrity requirements. Coordinate with designers, fabricators, and site engineers to resolve drawing issues. Support fabrication and erection teams with clarifications and revisions. Approve or comment on drawings within agreed timelines. Maintain drawing registers, revision control, and inspection records. Prepare inspection reports, non-conformance reports (NCRs), and corrective action follow-ups. Ensure as-built drawings reflect actual site conditions. Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.