Lifting engineer

Minimum Requirements: Proficient operation of SPMT control systems, including all steering modes and synchronized movements Strong understanding of load distribution, axle load calculations, and ground bearing pressures Ability to read and interpret transport drawings, method statements, and lift/transport plans High level of situational awareness in congested, high-risk work environments Effective radio and hand-signal communication with supervisors, banksmen, and rigging teams Solid knowledge of hydraulic, electrical, and power pack systems related to SPMTs Skilled in precision maneuvering of heavy and oversized loads under tight tolerances Competent in conducting pre-use inspections and basic fault finding Strong commitment to HSE compliance, hazard identification, and risk control Ability to remain calm and make sound decisions under pressure and time-critical conditions Team-oriented mindset with the ability to work closely with engineers and lifting crews Physical fitness and coordination suitable for long shifts and demanding site conditions Key Responsibilities: Safely operate SPMT units during heavy lift and transport operations in accordance with approved lift and transport plans Execute precise maneuvering, positioning, and alignment of loads under tight tolerance conditions Conduct pre-operation inspections of SPMT units, power packs, hydraulic systems, and control systems Monitor load stability, axle loads, steering modes, and ground bearing pressures throughout operations Follow approved method statements, risk assessments, and permit-to-work requirements at all times Communicate effectively with SPMT supervisors, engineers, riggers, and banksmen using radio and hand signals Respond promptly and correctly to abnormal conditions, alarms, and emergency situations Perform basic troubleshooting and first-line maintenance and report defects immediately Assist with SPMT configuration, coupling and decoupling of axle lines, and setup of power packs Ensure full compliance with HSE regulations, company procedures, and site-specific safety rules Maintain accurate operational logs, checklists, and inspection reports Support continuous improvement through participation in toolbox talks, safety briefings, and lessons learned Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.

Minimum Requirements: Strong ability to read, interpret, and review structural steel drawings (GA, shop, fabrication, and erection drawings). Solid understanding of steel structures design principles (connections, load paths, tolerances). Knowledge of international codes & standards: AISC, ASTM, AWS, EN, ISO, BS. Familiarity with welding symbols, WPS, NDT methods, and bolted connections. Understanding of material specifications (steel grades, bolts, coatings, fireproofing). Ability to identify design errors, clashes, and constructability issues. Software & Digital Skills: Proficiency in AutoCAD for drawing review and markups. Working knowledge of Tekla Structures or similar steel detailing software. Ability to review 3D models and BIM coordination drawings. Comfortable using document control systems and drawing registers. Basic skills in Excel for tracking comments, revisions, and inspections. Quality & Inspection Skills: Strong eye for detail and accuracy. Understanding of quality control procedures and inspection workflows. Ability to raise RFIs, NCRs, and technical comments clearly and professionally. Knowledge of inspection & test plans (ITPs) related to steel fabrication and erection. Key Responsibilities: Review and verify construction drawings (shop drawings, fabrication drawings, erection drawings) for steel and metal structures. Ensure compliance with project specifications, contracts, applicable codes, and standards (AISC, ASTM, EN, ISO, AWS, etc.). Check dimensional accuracy, connection details, tolerances, and material specifications. Confirm constructability and coordination with architectural, civil, mechanical, and electrical drawings. Identify design clashes, omissions, or inconsistencies and raise technical queries (RFIs). Verify materials (steel grades, bolts, welding consumables) match approved specifications. Review welding details (WPS, weld symbols, NDT requirements). Ensure corrosion protection systems are correctly specified (galvanizing, painting, coating systems). Confirm compliance with safety and structural integrity requirements. Coordinate with designers, fabricators, and site engineers to resolve drawing issues. Support fabrication and erection teams with clarifications and revisions. Approve or comment on drawings within agreed timelines. Maintain drawing registers, revision control, and inspection records. Prepare inspection reports, non-conformance reports (NCRs), and corrective action follow-ups. Ensure as-built drawings reflect actual site conditions. Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.

Minimum Requirements: Crane operation & controls – Confident operation of tower, mobile, crawler, and overhead cranes Load chart interpretation – Accurate assessment of weights, radii, and boom configurations Rigging knowledge – Proficient with slings, shackles, hooks, and load balancing Mechanical awareness – Ability to identify issues with hydraulics, cables, brakes, and safety systems Strong safety mindset – Continuous awareness of surroundings, personnel, weather, and site hazards Regulatory knowledge – Familiarity with OSHA, local regulations, site rules, and inspection standards Risk assessment – Demonstrated judgment to know when not to lift as a critical safety skill Key Responsibilities: Operate cranes and related equipment in a safe, precise, and efficient manner at all times Assemble, set up, rig, and dismantle cranes according to job and manufacturer requirements Function as crane operator, rigger, and signal person as required by staffing and job scope Determine and operate within lifting capacities in strict accordance with load charts Operate cranes based on written, verbal, and hand/signal instructions Conduct daily and periodic crane inspections, reporting any safety concerns or deficiencies Complete job tickets, crane inspection reports, and all required documentation accurately Operate additional equipment including fleet trucks, trailers, and support machinery Follow direction from supervisors and senior personnel while showing initiative and productivity Perform work for extended hours, often in adverse weather or site conditions, to meet project deadlines Maintain consistent, punctual attendance and a strong work ethic Work as a team player, fostering respectful and supportive relationships with coworkers Perform preventative maintenance including lubrication, cleaning, fluid sampling, replenishment, and component inspections Repair or replace worn or damaged components on heavy equipment as required Report any incident, hazard, or unethical activity that could impact company safety or operations to the Risk Manager Act as a mentor to less experienced employees and support team development Maintain all required certifications as mandated by law and company policy Remain in a constant state of alertness and operate in a safe, responsible manner Perform other duties as assigned Conditions: Location: Bayıl Working Schedule: Mon–Fri: 07:15 – 17:00/ Saturday: 07:15 – 15:30 Provided: Lunch & Transportation Salary: Based on interview result Interested candidates can send their cv to the e-mail address in the Apply for job button.